Tuesday, April 23, 2013

Kids' Cheesy Cardboard Camera

Hi everoyne!  

Happy belated Earth Day!

 Today I'll share about how I made this cheesy cardboard camera for Chuck.   This crapt was inspired by his love for eating cheese and touching my camera.  Here's what the camera looks like from the front:
 And here's what it looks like from the back:


Materials:
- small metal cylinder container with lid (or you could probably use a paper towel roll)
- can opener
- small, sturdy cardboard box
- craft knife
- scissors
- self-healing mat
- drill
- pencil
- 3 caps (I used 3 baby food squeeze pack caps)
- 3 brass fasteners
- packing tape
- lanyard (or string)
- disposable baking sheet (or plastic container lid or heavy duty aluminum foil)
- glue
- craft paint
- paint brushes and foam brush
- Mod Podge

Directions:
1.  I used a can opener to remove the bottom of my small, cylinder container.  I made sure that the can opener made clean cuts so that I wouldn't cut Chuck's fingers.  This cylinder became my camera "lens."

2.   The photo below shows my original box.  It was initially too big, so I chopped off a couple of inches off the right side of the box.  I used the cut off bits to fashion a top for the camera.

 3.  I cut out two circles, one in the front and one in the back of my camera.  The circle in the front was the same size as my cylinder.  (I just traced the cylinder and then cut the circle out.) The circle in the back of the box was slightly smaller than my cylinder.  (This ensured that my lens would poke out through the front, but not slide out through the back.)

4.  I also cut a rectangle from in the top, right hand corner of the front of my camera.  This became my "flash."

5.  Hubby drilled five holes in my cardboard:
- Two holes in the back to insert my back red knobs
- One hole on my top piece to insert my top green knob
- A hole on each side of the camera to string my lanyard strap through the body

He also drilled a hole into each of my three caps.  All the holes had to be big enough so that a fastener could fit through them.


 Here's a photo showing how the pieces fit together on the inside.  (I didn't use fasteners on the sides of my camera. I just poked them through the holes to show you where the holes were)

Here's how the camera  looked like with the top piece on:
I took this photo before cutting out the rectangle hole for the flash.
6.  After making sure my camera parts fit together, it was time to paint.  I gave the cardboard parts and cylinder two coats of yellow craft paint.  I also painted on my grey circles.
 7. Once the paint dried, I attached my "knobs", "lens", and "flash."  I used the brass fasteners to fasten the knobs onto the cardboard pieces.   I cut out a rectangle from my disposable baking pan and taped it over my rectangular "flash" hole.  I used a lot of packing tape to attach my cylinder to the inside of my camera.
8. I touched up my paint job a bit. Then, I coated my camera with Mod Podge to protect the paint.

9.  I strung lanyard through the body of the camera and then used glue and packing tape to attach the top piece to the body.

10.  To further protect my paint job, I ended up putting a thin strip of packing tape on the edges of the camera. (I've noticed that paint chips off the edges first, so I made sure to protect those with tape.)  I also put some tape near the lanyard hole in case the weight of the camera pulled on the lanyard and ripped the cardboard.

Phew.  Once I was done, I couldn't help but smile a cheesy grin.  (Hee hee.)  Here are some photos of Chuck playing around with his new cardboard camera.


Say "Cheese!"

Thanks for joining me on another crapty adventure.  If you're interested in making other crapty cardboard toys, check out my cardboard guitarcardboard rattle drumcereal box elephant, or cereal box giraffe.